亚洲影音-亚洲影视在线观看-五月伊人网-五月伊人婷婷-日韩字幕-日韩资源站-欧美一区亚洲一区-欧美一区亚洲-美女又爽又黄免费-美女又爽又黄-精品热-精品啪啪-国产麻豆自拍-国产麻豆一区二区-成人v-成人tv

當在地面預組裝之后將鍍鋅空氣管道安裝在頭上時預組裝長度的限制是為了防止由于鍍鋅空氣管道的自重引起的彎曲導致的部件界面的破壞。

The limitation on the length of pre assembly when installing galvanized air pipes on the head after pre assembly on the ground is to prevent damage to component interfaces caused by bending due to the weight of the galvanized air pipes.

軸通過鍍鋅風管垂直安裝由于空間小不便于以后維護所以鍍鋅風管一般采用夾套角鋼法蘭連接增加連接點的堅固性和強度并將法蘭變成一個“井”形狀吊架直接懸掛在凸耳上的角鋼法蘭上無需額外支撐。

The axis is vertically installed through galvanized air ducts. Due to the small space and inconvenient maintenance in the future, galvanized air ducts are generally connected by jacket angle steel flanges to increase the firmness and strength of the connection points and transform the flange into a "well" shape. The hanger is directly suspended on the angle steel flange on the lug without additional support.

非法蘭連接玻璃纖維復合板鍍鋅風管垂直安裝支撐件的生產和安裝方法。

Production and installation method of vertical installation support components for non flange connected glass fiber composite sheet galvanized air ducts.

在鍍鋅風管的榫眼接頭上涂上粘合劑以提高接頭的強度。

Apply adhesive to the mortise and tenon joints of galvanized air ducts to improve the strength of the joints.

應采取保護措施防止在運輸過程中損壞鍍鋅空氣管道。

Protective measures should be taken to prevent damage to galvanized air pipes during transportation.

玻璃纖維復合板鍍鋅風管端口用于切割表面裝配前法蘭連接器應用膠帶或膠水切割表面密封以防止玻璃纖維暴露和飛揚。

The galvanized air duct end of fiberglass composite plate is used to cut the surface. Before assembly, the flange connector should be sealed with tape or glue to cut the surface to prevent exposure and flying of fiberglass.

強度高強度小開孔性好錘形裝置長使用的原材料均采用彎輥生產3在外面和里面當聽到補語時會有二次撕裂?？涩F(xiàn)場制作可切割可鉆孔設備簡單省工省時85個。鍍鋅風管設備完工后不得進行防護。減少保護基金11號。鏡鋅板風管水平裝置長邊直徑或底寸小于或等于400mm間距不大于4m；大于400mm不宜大于3m鍍鋅風管支管、吊架間距可延長至5m和3.75m；鋼板法蘭鍍鋅框架間距不大于3m。

The hammer shaped device has high strength, small opening, and good performance. The raw materials used for long-term use are all produced by bending rollers. When the complement is heard on the outside and inside, there will be secondary tearing. The on-site production of cutting and drilling equipment is simple, labor-saving, and time-saving with 85 pieces. Galvanized air duct equipment shall not be protected after completion. Reduce Protection Fund No. 11. The long side diameter or bottom dimension of the mirror zinc plate air duct horizontal device is less than or equal to 400mm, and the spacing is not more than 4m; For galvanized air duct branches and hangers larger than 400mm and not larger than 3m, the spacing can be extended to 5m and 3.75m; The spacing between galvanized steel plate flanges and frames shall not exceed 3m.

紅外線管道支吊架應強度和強度的選擇模式和標準符合gb atls和標準。特種鍍鋅板風管支吊架風口、閥門、檢修門及自控機構與風口或堵頭的間距鑫{痧機加工后的吊桿應螺紋完好光亮。每個輔助支撐器和吊架應力可用于振動沖擊支吊架的拆卸或吊裝

The selection mode and standards for the strength of infrared pipeline supports and hangers should comply with GB ATLS and standards. The spacing between the air vent, valve, maintenance door, and self-control mechanism of the special galvanized sheet air duct support and hanger, as well as the air vent or plug, should be intact and bright after machining. The stress of each auxiliary support and hanger can be used for the disassembly or hoisting of vibration impact support and hanger